Bis Certifications

Scheme Of Inspection and Testing

 1. LABORATORY - A laboratory shall be maintained which shall be suitably equipped and staffed, where different tests given in the specification shall be carried out in accordance with the methods given in the specification. 1.1 The manufacturer shall prepare a calibration plan for the test equipment.

2. TEST RECORDS – The manufacturer shall maintain test records for the tests carried out to establish conformity.

3. LABELLING AND MARKING – The labelling and marking on each and every product as per the BIS guidelines should be permanently affixed, resistant to remove, scratching and should not be easily washed off.

 

IS 14862: 2000 categorizes fibre cement flat sheets into type categories based on rupture modulus. The sheets are categorized into length, width, and thickness. Grouping guidelines for GoL/CSoL include testing one sample of the highest nominal thickness from each type and category, as well as sheets with declared additional characteristics. Firms must declare the varieties they intend to cover in the license, which may be restricted based on manufacturing and testing capabilities. BO must ensure all varieties are tested in rotation.

 

IS 3513 (Part 3): 1989 categorizes Resin Treated Compressed Wood Laminates (Compregs) into general purposes, categorized into Grades (General-Purpose High-Density Grade and General-Purpose Medium Density Grade), Types (II, III, V, and VI), Board dimensions (in mm), Thickness (in mm), and Rod dimensions (in mm). Compregs are grouped based on press capacity and thickness (in mm). Manufacturing of higher thickness/diameter compregs is more critical than lower thickness/diameter compregs. Grouping guidelines for GoL/CSoL include testing one sample of compreg board and rod for all requirements, including thickness up to and including the specified grade and type. If board/rod of Type V or Type VI is covered, board/rod of Type II and Type III of that particular grade may also be included. Additional special sizes/shapes may be covered under the license, subject to compliance with dimensions requirements. The Firm must declare the varieties they intend to cover in the License and ensure all varieties are tested in rotation during operation.

 

 

IS 3513 (Part 2): 1989 categorizes Resin Treated Compressed Wood Laminates (Compregs) for chemical purposes into Types V and VI, board dimensions (in mm), thickness (in mm), and rod dimensions (in mm). Compregs are grouped based on press capacity and thickness (in mm). Manufacturing of higher thickness/diameter compregs is more critical than lower thickness/diameter compregs. Grouping guidelines for GoL/CSoL include testing one sample of compreg board and rod for all requirements, including thickness up to and including the specified type. Additional special sizes/shapes may be covered in the scope of the license, subject to compliance with dimensions requirements. The firm must declare the varieties they intend to cover in the license, and the scope may be restricted based on the manufacturer's manufacturing and testing capabilities. BO must ensure all varieties are tested in rotation during the license operation.

 

 

IS 3513 (Part 1): 1989 categorizes Resin Treated Compressed Wood Laminates (Compregs) for electrical purposes into various types, dimensions, and thicknesses. Boards are categorized into lengths (i.e., 2400, 2100, 1800, 1500, 1200, 900, 600), widths (i.e., 1200, 900, 600, 300, and 150), and thicknesses (i.e., 3, 4, 5, 6, 8, 12, 16, 20, 25, 32, 40, 50, 60, and 70). Rods are categorized into lengths (i.e., 1500, 1200, 900, 600), diameters (8 to 50, 3, to 50, 50 to 80), and more. Manufacturing of higher thickness/diameter compregs is more critical than lower thickness/diameter compregs. Grouping guidelines for GoL/CSoL include testing one sample of compreg board and rod for all requirements, including the type tested in the scope of the license. The firm must declare the varieties they intend to cover in the license and ensure all varieties are tested in rotation during operation.

 

                       Scheme Of Inspection and Testing

 

 1. LABORATORY - A laboratory shall be maintained which shall be suitably equipped and staffed, where different tests given in the specification shall be carried out in accordance with the methods given in the specification. 1.1 The manufacturer shall prepare a calibration plan for the test equipment.

2. TEST RECORDS – The manufacturer shall maintain test records for the tests carried out to establish conformity.

3. LABELLING AND MARKING – The labelling and marking on each and every product as per the BIS guidelines should be permanently affixed, resistant to remove, scratching and should not be easily washed off.

                                                                Grouping Guidelines

The guidelines for Grant of Licence (GoL)/Change in Scope of Licence (CSoL) include testing gloves of different sizes, restricting the license's scope based on manufacturer's capabilities, and testing products in rotation during license operation.

       . 

Scheme Of Inspection and Testing

 1. LABORATORY - A laboratory shall be maintained which shall be suitably equipped and staffed, where different tests given in the specification shall be carried out in accordance with the methods given in the specification. 1.1 The manufacturer shall prepare a calibration plan for the test equipment.

2. TEST RECORDS – The manufacturer shall maintain test records for the tests carried out to establish conformity.

3. LABELLING AND MARKING – The labelling and marking on each and every product as per the BIS guidelines should be permanently affixed, resistant to remove, scratching and should not be easily washed off.

 

                                                                Grouping Guidelines

IS 1475 (Part 1) covers water coolers of various types, including pressure type, bubbler type, faucet type, and storage type. Pressure type water coolers are grouped based on cooling capacity, with samples tested for both types. Storage type water coolers must be tested for both cooling capacity and storage capacity. Single/Three phase water coolers must be tested separately. Firms must declare their intended varieties in their license, which may be restricted based on manufacturing capabilities and testing facilities. During operation, all licensees must be tested in rotation.

 

Scheme Of Inspection and Testing

 1. LABORATORY - A laboratory shall be maintained which shall be suitably equipped and staffed, where different tests given in the specification shall be carried out in accordance with the methods given in the specification. 1.1 The manufacturer shall prepare a calibration plan for the test equipment.

2. TEST RECORDS – The manufacturer shall maintain test records for the tests carried out to establish conformity.

3. LABELLING AND MARKING – The labelling and marking on each and every product as per the BIS guidelines should be permanently affixed, resistant to remove, scratching and should not be easily washed off.

 

                                                                Grouping Guidelines

Wire of each size (nominal diameter) shall be tested to cover that size for GoL or CSoL

 

The ISI Mark Certification for Poly-Laminated Aluminium Cable Wrap is governed by Indian Standard IS 16012:2012, which specifies the requirements for poly-laminated aluminum wraps used as protective sheathing for electrical cables. This wrap provides a barrier against moisture, corrosion, and mechanical damage, ensuring the longevity and safety of electrical cables, particularly in harsh environments.

1) IS 14810:200 covers phosphorized(DHP) copper tubes for general plumbing and similar applications for the convenience of fluids including water.
2) These tubes shall be designated by the outside diameter and the wall thickness, as given in Tables W, X,Y,Z. Further, these tubes can supplied in either of the 3 conditions namely Hard(HD), Half Hard (HB), Annealed(soft) (O).
3) In view of above, it is proposed to have the following grouping guidelines for the purpose of GoL/CSoL
4) However, it shall be ensured that the firm is having all the necessary manufacturing and testing facilities for manufacturing/testing of all the sizes and conditions covered in the scope of the licence.
5) During the operation of the licence, BOs shall ensure that all sizes and conditions covered in the scope of the licence are drawn for independent testing in rotation over a period of time.

• Minimum Order Quantity: 1 Certificate
• Delivery Time: 30-40 Days

1) IS 2501:1994 covers the requirements of solid drawn (seamless) copper tubes for general engineering purposes. This standard covers seven grades of copper tubes namely Cu-ETP, Cu-DHP, Cu-FRTP, Cu-DPA and Cu-ATP as specified in IS 191 (Copper Specification).
2) Further, these tubes shall be supplied either of the 3 conditions namely As Drawn(HD), Half Hard (HB), Annealed (O).
3) In view of above, it is proposed to have the following grouping guidelines for the purposeof GoL/CSoL
4) The above samples drawn shall be such which: a) Cover the entire range of sizes (wall thickness and outside diameter) of tubes intendedtobe covered in the licence (such as lowest, intermediate and highest sizesaspermanufacturing capability). b) Cover all conditions (As drawn(HB), Half Hard (HB) & Annealed (O)) of supplyof Tubesintended to be covered in the licence.
5) Scope of licence shall be restricted based on the manufacturing and testing facilities available.
6) During operation of licence, samples of each variety covered in the scope of licence, shall betested in rotation, to the extent possible

• Minimum Order Quantity: 1 Certificate
• Delivery Time: 30-40 Days

1) IS 1545:1994 covers the requirements of solid drawn (seamless) copper and copper alloytubes of outside diameters 5 mm to 80 mm for use in condensers and heat exchangers. Thisstandard covers seven grades of copper and copper alloy tubes as given in Table 1.
2) Further, these tubes shall be supplied either of the 5 conditions namely As Drawn(HD), AsDrawn and End Annealed, Half Hard (HB), Temper Annealed (TA), Annealed (O).
3) In view of above, it is proposed to have the following grouping guidelines for the purposeof GoL/CSoL
4) The above samples drawn shall be such which:a( Cover the entire range of sizes )wall thickness and outside diameter( of tubes intendedtobe PM/1545/2April 2024covered in the licence )such as lowest, intermediate and highest sizes as per manufacturingcapability(. b( Cover all conditions )As drawn)HB(, As Drawn and Annealed )HD(, Half Hard)HB(, TemperAnnealed )TA( & Annealed )O(( of supply of Tubes intended to be covered in the licence.

5. Scope of licence shall be restricted based on the
manufacturing and testing facilities available.
6. During operation of licence, samples of each variety covered in the scope of licence, shall betestedin rotation, to the extent possible

• Minimum Order Quantity: 1 Certificate
• Delivery Time: 40-50

1) The following grouping guidelines shall apply for Grant of Licence (GoL)/Change in Scope of Licence(CSoL): i)Samples of each Grade (Cu-ETP, Cu-FRHC) to be drawn and tested. ii)Samples of each Condition ( O (Annealed), HB (Half Hard) and HD (Hard)) to be drawn and tested. iii) Samples of each Shape (Round, Square and Hexagonal, Rectangular) to be drawn and tested tested.
2) While drawing samples of different sizes from the above groups, samples may be drawn in such combination which cover all Grades, all Conditions and all Shapes, intended to be covered in the scope of the licence.
3) For inclusion of a particular Grade, Condition or Shape in the existing Scope of licence, sample of that Grade/Condition/Shape, of any size within the range of sizes covered in the existing scope of licence, shall be tested separately. 4) Scope of the licence shall be restricted based on the manufacturing and testing facilities available.
5) During the operation of the licence, samples of each variety covered in the scope of licence, shall betested in rotation, to the extent possible.

• Minimum Order Quantity: 1 Certificate
• Delivery Time: 30-40 DAYS

Possible tests in a day
Workmanship and Finish (Cl. 5.1), Tensile Strength, Water proofness and absorption (Table 1) may be tested in a day if conditioned samples are available

• Minimum Order Quantity: 1 Certificate
• Delivery Time: 40-50 Days

Grouping Guidelines
1. For the purpose of certification, following technical parameters are considered for classifications of “Evaporative Air Coolers (Desert Coolers)” into different varieties as per IS 3315: 2019
2. A variety may be defined as group of models having the same value of these technical

• Minimum Order Quantity: 1 Certificate
• Delivery Time: 40-50 DAYS+

Scheme Of Inspection and Testing

 1. LABORATORY - A laboratory shall be maintained which shall be suitably equipped and staffed, where different tests given in the specification shall be carried out in accordance with the methods given in the specification. 1.1 The manufacturer shall prepare a calibration plan for the test equipment.

2. TEST RECORDS – The manufacturer shall maintain test records for the tests carried out to establish conformity.

3. LABELLING AND MARKING – The labelling and marking on each and every product as per the BIS guidelines should be permanently affixed, resistant to remove, scratching and should not be easily washed off.

                                                                Grouping Guidelines

Asbestos cement pressure pipes and joints are classified based on pressure class (10, 15, 20, or 25), nominal diameter (50 mm to 1000 mm), and type of joint (asbestos cement coupling with rubber sealing rings or cast iron detachable joints with rubber sealing rings and bolts and nuts). Grouping guidelines for GoL/CSoL include testing two pipes of any size and two joints of any type for all requirements. Manufacturers must submit testing data for pressure class other than 10, 15, 20, and 25 and sizes above 1000 mm. The scope of license may be restricted based on manufacturer's capabilities.

 

Scheme Of Inspection and Testing

 1. LABORATORY - A laboratory shall be maintained which shall be suitably equipped and staffed, where different tests given in the specification shall be carried out in accordance with the methods given in the specification. 1.1 The manufacturer shall prepare a calibration plan for the test equipment.

2. TEST RECORDS – The manufacturer shall maintain test records for the tests carried out to establish conformity.

3. LABELLING AND MARKING – The labelling and marking on each and every product as per the BIS guidelines should be permanently affixed, resistant to remove, scratching and should not be easily washed off.

 

                                                                Grouping Guidelines

The classification of High Carbon Steel Wire Rods is based on chemical composition, tensile strength, partial decarburization limits, and wire rod sections. Tests for non-metallic inclusions and maximum resolvable pearlite limits are only conducted if agreed upon between the manufacturer and purchaser. Samples for independent testing are drawn from HC38 to HC88, covering all sizes, grades, and shapes. For Type-X wire rods, samples are drawn from Type-X. For HCT535 to HCT1250, samples are drawn from HCT535 to HCT1250, covering all sizes, grades, and shapes. The firm must ensure it has necessary manufacturing and testing facilities for the entire range of sizes/classes proposed. During the license operation, all sizes/grades covered are drawn for independent testing on rotation over a period of time.

 

Scheme Of Inspection and Testing

 1. LABORATORY - A laboratory shall be maintained which shall be suitably equipped and staffed, where different tests given in the specification shall be carried out in accordance with the methods given in the specification. 1.1 The manufacturer shall prepare a calibration plan for the test equipment.

2. TEST RECORDS – The manufacturer shall maintain test records for the tests carried out to establish conformity.

3. LABELLING AND MARKING – The labelling and marking on each and every product as per the BIS guidelines should be permanently affixed, resistant to remove, scratching and should not be easily washed off.

 

                                                                Grouping Guidelines

The hot rolled steel strip for welded tubes and pipes is classified based on increasing minimum yield stress and decreasing elongation. To grant a license or inclusion, one sample of any size/mode of de-oxidation of carbon steel strip of Highest and Lowest Yield Stress must be drawn for testing. Grades including and between those strength limits may be covered in the scope of the license. The appropriate undertaking/declaration and micro-alloying contents may be reflected in the test request.

 

 

Scheme Of Inspection and Testing

 1. LABORATORY - A laboratory shall be maintained which shall be suitably equipped and staffed, where different tests given in the specification shall be carried out in accordance with the methods given in the specification. 1.1 The manufacturer shall prepare a calibration plan for the test equipment.

2. TEST RECORDS – The manufacturer shall maintain test records for the tests carried out to establish conformity.

3. LABELLING AND MARKING – The labelling and marking on each and every product as per the BIS guidelines should be permanently affixed, resistant to remove, scratching and should not be easily washed off.

 

                                                                Grouping Guidelines

The IS 15155:2020 classification of bar/wire wrapped steel cylinder pipes with mortar lining and coating is based on size (250 mm to 1900 mm), factory test pressure (to be declared by the manufacturer), and type of ends/joints (steel socket and spigot ring). Pipes with internal diameters other than those specified in Table 1 and pipes for working pressure higher than 28 kg/cm2 may be supplied by mutual agreement. Pipes/specials are further classified into groups based on minimum wall thickness. The firm must declare the varieties they intend to cover in the license and ensure all varieties are tested in rotation.

 

Scheme Of Inspection and Testing

 1. LABORATORY - A laboratory shall be maintained which shall be suitably equipped and staffed, where different tests given in the specification shall be carried out in accordance with the methods given in the specification. 1.1 The manufacturer shall prepare a calibration plan for the test equipment.

2. TEST RECORDS – The manufacturer shall maintain test records for the tests carried out to establish conformity.

3. LABELLING AND MARKING – The labelling and marking on each and every product as per the BIS guidelines should be permanently affixed, resistant to remove, scratching and should not be easily washed off.

 

                                                                Grouping Guidelines

IS 2835: 1987 classifies sheet glass into four grades: AA, A, B, and C. For licenses or scope changes, separate samples must be tested for each quality, and samples of the highest and lowest thicknesses must be drawn. Licenses may be granted or changed if samples pass testing, and the firm must have necessary facilities for manufacturing and testing.

 

Scheme Of Inspection and Testing

 1. LABORATORY - A laboratory shall be maintained which shall be suitably equipped and staffed, where different tests given in the specification shall be carried out in accordance with the methods given in the specification. 1.1 The manufacturer shall prepare a calibration plan for the test equipment.

2. TEST RECORDS – The manufacturer shall maintain test records for the tests carried out to establish conformity.

3. LABELLING AND MARKING – The labelling and marking on each and every product as per the BIS guidelines should be permanently affixed, resistant to remove, scratching and should not be easily washed off.

 

                                                                Grouping Guidelines

Each Type of Domestic Gas Stove for use with LPG shall be tested for GoL/CSoL

Scheme Of Inspection and Testing

 1. LABORATORY - A laboratory shall be maintained which shall be suitably equipped and staffed, where different tests given in the specification shall be carried out in accordance with the methods given in the specification. 1.1 The manufacturer shall prepare a calibration plan for the test equipment.

2. TEST RECORDS – The manufacturer shall maintain test records for the tests carried out to establish conformity.

3. LABELLING AND MARKING – The labelling and marking on each and every product as per the BIS guidelines should be permanently affixed, resistant to remove, scratching and should not be easily washed off.

 

                                                                Grouping Guidelines

IS 4296 (Part2) covers various types of punches with cylinder heads and reduced shanks, including A, B, BS, BR, OB, C, D, E, F, FS, FR, and FO. The standard does not restrict the use of other materials, but manufacturers must declare the materials and their hardness values, and inform BIS of any changes or additions during the license's operation. Certain dimensions of punches are left to manufacturer's discretion, and declarations must be obtained for dimensions and tolerance. The license scope may be restricted based on the manufacturer's manufacturing and testing capabilities. BO must ensure all punches are tested in rotation during the license's operation.

 

GROUPING GUIDELINES
1) Designations have been grouped based upon their aluminum purity/major alloying element content. For the purpose of GoL/CSoL, the following grouping guidelines may be considered
2) The sample(s) drawn above can be of any size of forging/forging stock. However, sample of each Condition(Temper) (cl.6.1) is required to be drawn to cover the Conditions (Tempers) intended to be covered in the licence.
3) The requirement of Tolerances (cl.7.) of IS 734:1975 shall be tested in the factory on the sizes of forging stock or forgings, as agreed to between the manufacturer and purchaser, offered during inspection, from which samples are drawn for TPT.
4)However, it shall be ensured that the firm is having all the necessary manufacturing and testing facilities for manufacturing/testing of all the designations/conditions covered in the scope of the licence.
5) During the operation of the licence, BOs shall ensure that all designations/conditions covered in the scope of the licence are drawn for independent testing in rotation over a period of time.

• Minimum Order Quantity: 1 Certificate
• Delivery Time: 40-50 DAYS

Grouping Guidelines
1. Asbestos cement pressure pipes and Joints are classified as given below
a) Pressure Class – 10, 15, 20 and 25 ( Other pressure classes such as 12, 18, 24, 30, 35 and 36 may also be manufactured where detailed dimensions shall be as agreed to between manufacturer and purchaser).
b) Size (Nominal Diameter) - 50 mm to 1000 mm (Pipes of nominal diameter above 1000 mm may also be manufactured as per agreement between manufacturer and user).
c) Type of Joint – (a) Asbestos cement coupling with rubber sealing rings (b) Cast Iron detachable joints with rubber sealing rings and bolts and nuts. 2. Asbestos cement pressure pipes and Joints are grouped as given below based on Size (Nominal Diameter): 

• Minimum Order Quantity: 1 Certificate
• Delivery Time: 40-50 DAYS

Grouping Guidelines

1. IS 4003 (Part 1) covers General Purposes Pipe Wrenches of the following Nominal Sizes:
 200 mm, 250 mm, 300 mm, 350 mm, 450 mm, 600 mm, 900 mm, 1200 mm
2. Considering the above, the grouping guidelines given below shall be followed for GoL/CSoL:
 Sample of lowest and highest size shall be tested for all requirements to cover all sizes in that size range.
3. The Firm shall declare the varieties of Wrenches intended to be covered in the Licence. The Scope of Licence may be restricted based on the Manufacturing and Testing capabilities of the Manufacturer.
4. During operation of the licence, BO shall ensure that all the varieties covered in the licence are tested in rotation to the extent possible.  

GROUPING GUIDELINES
1) Wrought Aluminum and Aluminum Alloy Sheets and Strip as per IS 737:2008 are classified into various designations based upon the major alloying element as per Table 1 . Further, these designations could be supplied in the conditions (temper designations such as O, Hx2, Hx4, T4, T6 etc.) as per the desired mechanical properties as per Table 2.
2) Designations, as specified at Table 1, have been grouped into the following groups based upon the major alloying elements and are arranged in order of least to most stringent based upon the purity/percentage of major alloying element
3) In view of above, the following grouping guidelines may be considered for GoL/CSoL:- a) From each group if sample of higher purity/higher percentage of major alloying element is drawn the lower designations may be covered for same temper designation. b) Separate samples under each group are to be drawn for each Temper Condition intended to be included in Scope of Licence. c) The sample drawn above shall be of any size and separate samples for all sizes intended to be covered in the licence are not required to be drawn.
4) However, it shall be ensured that the firm is having all the necessary manufacturing and testing facilities for the manufacture and testing of the varieties to be included in the licence.

• Minimum Order Quantity: 1 Certificate
• Delivery Time: 30-40 DAYS

GROUPING GUIDELINES
1) Designations have been grouped based upon their aluminum purity/major alloying element content. For the purpose of GoL/CSoL, the following grouping guidelines may be considered
2) The sample(s) drawn above shall be of the smallest diameter of bars/wires being manufactured. Further, sample of each Condition(Temper) (cl.6.1) is required to be drawn to cover the Conditions (Tempers) intended to be covered in the licence.
3) However, it shall be ensured that the firm is having all the necessary manufacturing and testing facilities for manufacturing/testing of all the designations/conditions/sizes covered in the scope of the licence.
5) During the operation of the licence, BOs shall ensure that all designations/conditions/sizes covered in the scope of the licence are drawn for independent testing in rotation over a period of time.

• Minimum Order Quantity: 1 Certificate
• Delivery Time: 30-40 DAYS

Possible tests in a day
a) Length
b) Width
c) Mass
d) Average breaking strength of wind shield net fabric, Warpway & Weftway
e) Colour fastness to artificial light
f) Bursting pressure g) Wind blockag

• Minimum Order Quantity: 1 Certificate
• Delivery Time: 40-50 Days

a) Length
b) Width
c) Mass
d) Average breaking strength of Harvest net fabric, Warpway & Weftway
e) Colour fastness to artificial light f) Bursting pressure g) Air Permeability

• Minimum Order Quantity: 1 Certificate
• Delivery Time: 40-50 Days

Scheme Of Inspection and Testing

 1. LABORATORY - A laboratory shall be maintained which shall be suitably equipped and staffed, where different tests given in the specification shall be carried out in accordance with the methods given in the specification. 1.1 The manufacturer shall prepare a calibration plan for the test equipment.

2. TEST RECORDS – The manufacturer shall maintain test records for the tests carried out to establish conformity.

3. LABELLING AND MARKING – The labelling and marking on each and every product as per the BIS guidelines should be permanently affixed, resistant to remove, scratching and should not be easily washed off.

                                                                Grouping Guidelines

Parliament hinges are classified based on material size, with Type 1 being Cast Cast brass, Type 2 being Pressed Mild steel, and Type 3 being Fabricated Extruded aluminum alloy. Samples of each type must be tested to cover all sizes in the size range. Firms must declare the varieties they intend to cover in the license, and BO must ensure all varieties are tested in rotation.

 

Scheme Of Inspection and Testing

 1. LABORATORY - A laboratory shall be maintained which shall be suitably equipped and staffed, where different tests given in the specification shall be carried out in accordance with the methods given in the specification. 1.1 The manufacturer shall prepare a calibration plan for the test equipment.

2. TEST RECORDS – The manufacturer shall maintain test records for the tests carried out to establish conformity.

3. LABELLING AND MARKING – The labelling and marking on each and every product as per the BIS guidelines should be permanently affixed, resistant to remove, scratching and should not be easily washed off.

                                                                Grouping Guidelines

IS 453: 1993 classifies Double-Acting Spring Hinges into different varieties based on material and size. Samples must be drawn from each type to cover all sizes and materials. Firms must declare their varieties in their license, which may be restricted based on manufacturing and testing capabilities.

 

With precise knowledge of the relevant field, we have been able to offer the commendable range of BIS Certification Consultant Service to our valuable clients. Also, our offered consultant services are rendered by knowledgeable personnel, who enable us to render the exact specifications of our customers.     

• Item Code: Is-17265
• Delivery Time: 40-50

Scheme Of Inspection and Testing

 1. LABORATORY - A laboratory shall be maintained which shall be suitably equipped and staffed, where different tests given in the specification shall be carried out in accordance with the methods given in the specification. 1.1 The manufacturer shall prepare a calibration plan for the test equipment.

2. TEST RECORDS – The manufacturer shall maintain test records for the tests carried out to establish conformity.

3. LABELLING AND MARKING – The labelling and marking on each and every product as per the BIS guidelines should be permanently affixed, resistant to remove, scratching and should not be easily washed off.

 

                                                                Grouping Guidelines

Electric Kitchen Machine samples must be tested based on product type, functionality, voltage, input power, appliance class, insulation class, and water protection degree. Varieties with lower protection levels may be covered. Firms must declare their intended varieties in the license, which may be restricted based on manufacturing capabilities. BO must ensure all varieties are tested in rotation during operation.

 

Scheme Of Inspection and Testing

 1. LABORATORY - A laboratory shall be maintained which shall be suitably equipped and staffed, where different tests given in the specification shall be carried out in accordance with the methods given in the specification. 1.1 The manufacturer shall prepare a calibration plan for the test equipment.

2. TEST RECORDS – The manufacturer shall maintain test records for the tests carried out to establish conformity.

3. LABELLING AND MARKING – The labelling and marking on each and every product as per the BIS guidelines should be permanently affixed, resistant to remove, scratching and should not be easily washed off.

 

                                                                Grouping Guidelines

IS 11169 (Part 1):2022 is a standard for unalloyed and alloyed steels intended for cold heading or cold extruding applications. It covers three groups of steels: non-alloy steels, case-hardening steels, and steels for quenching and tempering. These steels can be supplied in different delivery conditions, as specified in Tables A.1, B.1, and C.1. Mechanical properties for each group are specific to the delivery condition and the type of steel. Case-hardening steels and steels for quenching and tempering can be supplied with hardenability requirements (cl.8.2) of three types: Standard Hardenability (HH), Restricted Hardenability (HL), and Core Hardenability (CH). For wire rods/bars/wires, shapes, dimensions, and tolerances are specified, with h6 being the most stringent tolerances class. For bright steel products, separate tolerance classes (h6 to h12) are specified in accordance with IS 919 (part 2), with h6 being the most stringent. The standard also provides guidelines for the grouping of steels for Gol/CSoL, including product shape, size, finish, tolerance class, and delivery conditions.

 

Scheme Of Inspection and Testing

 1. LABORATORY - A laboratory shall be maintained which shall be suitably equipped and staffed, where different tests given in the specification shall be carried out in accordance with the methods given in the specification. 1.1 The manufacturer shall prepare a calibration plan for the test equipment.

2. TEST RECORDS – The manufacturer shall maintain test records for the tests carried out to establish conformity.

3. LABELLING AND MARKING – The labelling and marking on each and every product as per the BIS guidelines should be permanently affixed, resistant to remove, scratching and should not be easily washed off.

 

                                                                Grouping Guidelines

The IS 4368:1967 allows for one sample to be drawn and tested from each grade for chemical and hardness tests, covering all sizes of that grade. If a manufacturer applies for GOL/Inclusion of multiple product types, one sample can be drawn and tested.

 

Scheme Of Inspection and Testing

 1. LABORATORY - A laboratory shall be maintained which shall be suitably equipped and staffed, where different tests given in the specification shall be carried out in accordance with the methods given in the specification. 1.1 The manufacturer shall prepare a calibration plan for the test equipment.

2. TEST RECORDS – The manufacturer shall maintain test records for the tests carried out to establish conformity.

3. LABELLING AND MARKING – The labelling and marking on each and every product as per the BIS guidelines should be permanently affixed, resistant to remove, scratching and should not be easily washed off.

 

                                                                Grouping Guidelines

The classification of stainless steel grade designations is based on the phase of iron and chemical composition/alloying elements. Guidelines for drawing samples for each group include X04Cr13 for ferritic, X12Cr13 for martensitic, and X02Cr18Ni11 for austenitic. A declaration on each heat treatment process is required for each group. If the samples pass, a license can be granted for all sizes and varieties of the group, provided the firm has the necessary facilities for manufacturing and testing. During the license operation, all sizes/grade designations/varieties are drawn for independent testing over time.

 

Scheme Of Inspection and Testing

 1. LABORATORY - A laboratory shall be maintained which shall be suitably equipped and staffed, where different tests given in the specification shall be carried out in accordance with the methods given in the specification. 1.1 The manufacturer shall prepare a calibration plan for the test equipment.

2. TEST RECORDS – The manufacturer shall maintain test records for the tests carried out to establish conformity.

3. LABELLING AND MARKING – The labelling and marking on each and every product as per the BIS guidelines should be permanently affixed, resistant to remove, scratching and should not be easily washed off.

 

                                                                Grouping Guidelines

The product's manufacturing process is divided into three groups based on % C, P & S. The first group tests samples of higher formability grades without micro-alloy elements, while the second group tests samples of higher formability grades with micro-alloying elements. The third group tests samples of each grade applied for, preferably with high % C, % Mn and micro-alloy elements. The scope of the license is restricted based on available manufacturing and testing facilities. During the operation of the license, samples of each variety covered in the scope must be tested in rotation to the extent possible. The license scope is based on the available manufacturing and testing facilities.

 

Scheme Of Inspection and Testing

 1. LABORATORY - A laboratory shall be maintained which shall be suitably equipped and staffed, where different tests given in the specification shall be carried out in accordance with the methods given in the specification. 1.1 The manufacturer shall prepare a calibration plan for the test equipment.

2. TEST RECORDS – The manufacturer shall maintain test records for the tests carried out to establish conformity.

3. LABELLING AND MARKING – The labelling and marking on each and every product as per the BIS guidelines should be permanently affixed, resistant to remove, scratching and should not be easily washed off.

 

                                                                Grouping Guidelines

The product is classified into Class 1, Class 2, Class 3, and Class 4 based on the durability of Organic Coating, with Class 4 being the most stringent due to the duration of salt spray and humidity resistance tests. Manufacturers can specify other durations of Durability Tests, but these are for informational purposes only. The Grouping Guideline for licenses includes testing one sample of each Durability Class of Paint Coating for all requirements, declaring the duration of Durability Tests, and covering Class 0 when a sample conforms. The scope of the license is restricted based on available facilities and samples must be tested in rotation.

 

Scheme Of Inspection and Testing

 1. LABORATORY - A laboratory shall be maintained which shall be suitably equipped and staffed, where different tests given in the specification shall be carried out in accordance with the methods given in the specification. 1.1 The manufacturer shall prepare a calibration plan for the test equipment.

2. TEST RECORDS – The manufacturer shall maintain test records for the tests carried out to establish conformity.

3. LABELLING AND MARKING – The labelling and marking on each and every product as per the BIS guidelines should be permanently affixed, resistant to remove, scratching and should not be easily washed off.

 

                                                                Grouping Guidelines

The hot rolled steel strip for welded tubes and pipes is classified based on minimum yield stress and tensile strength. Licenses and inclusions are granted based on the following guidelines: one sample of any size, mode of de-oxidation of the highest yield strength, and the appropriate undertaking/declaration. The manufacturer must ensure complete manufacturing facilities and testing equipment are available for all requirements when considering licenses or inclusions of additional varieties.

 

Scheme Of Inspection and Testing

 1. LABORATORY - A laboratory shall be maintained which shall be suitably equipped and staffed, where different tests given in the specification shall be carried out in accordance with the methods given in the specification. 1.1 The manufacturer shall prepare a calibration plan for the test equipment.

2. TEST RECORDS – The manufacturer shall maintain test records for the tests carried out to establish conformity.

3. LABELLING AND MARKING – The labelling and marking on each and every product as per the BIS guidelines should be permanently affixed, resistant to remove, scratching and should not be easily washed off.

 

                                                                Grouping Guidelines

The Hot Dip Aluminum - Zinc Alloy Metallic Coated Steel Strip and Sheet, according to IS 15961: 2012, is classified based on grade designation and coating class. The manufacturer must have complete manufacturing and testing arrangements for the varieties covered in the license. During the operation of the license, samples must be drawn during surveillance visits on a rotation basis to cover all grades included in the license. Surface treatment and finish recommendations should be based on manufacturing facilities. The company must ensure all sizes and processes covered in the license are drawn for independent testing on rotation over time.

 

GROUPING GUIDELINES
The following grouping guidelines shall apply for Grant of Licence (GoL)/Change in Scope of Licence (CSoL): IS 17731:2021 classifies the product into 4 types : Types 1,2,3,4 based on the thickness and mass, in g/m2 and type of reinforcement at edges of woven fabric. Types 1 and 3 are without laminated reinforcement band at the edges while Types 2 and 4 are with laminated reinforcement band at the edges. Considering the above, the product is classified for the purpose of these guidelines, into 2 groups as follows: Group 1 – Type 1 and 2 Group 2 – Type 3 and 4 From group 1, if sample of type 2 (i.e. with laminated reinforcement band at the edges) is tested, then type 1 can be covered in the scope on that basis. From group 2, if sample of type 4 (i.e. with laminated reinforcement band at the edges) is tested, then type 3 can be covered in the scope on that basis. Scope of the licence shall be restricted based on the manufacturing and testing capabilities. During the operation of the licence, samples of each variety covered in the scope of licence shall be tested, to the extent possible.

• Minimum Order Quantity: 1 Certificate
• Delivery Time: 30-40 DAYS

Scheme Of Inspection and Testing

 1. LABORATORY - A laboratory shall be maintained which shall be suitably equipped and staffed, where different tests given in the specification shall be carried out in accordance with the methods given in the specification. 1.1 The manufacturer shall prepare a calibration plan for the test equipment.

2. TEST RECORDS – The manufacturer shall maintain test records for the tests carried out to establish conformity.

3. LABELLING AND MARKING – The labelling and marking on each and every product as per the BIS guidelines should be permanently affixed, resistant to remove, scratching and should not be easily washed off.

                                                                Grouping Guidelines

IS 205:92 classifies stainless steel butt hinges into three types: extruded aluminium alloy, extruded brass, cast brass, and sheet brass. The grouping guidelines for GoL/CSoL include testing one sample from each type, declaring the varieties they intend to cover in the license, and ensuring all varieties are tested in rotation during operation. The scope of the license may be restricted based on the manufacturer's manufacturing and testing capabilities.

 

All Portland Pozzolana Cement-Part 2 Calcined clay based has been included in the mandatory ISI Certification Scheme under IS standard - IS 1489 (Part-2). This product cannot be exported/imported or sold in Indian consumer market without ISI Mark imprinted. We provide complete ISI Certification consultancy services for your product from start to end, during which assist you in all types of documentation formalities and we take care of all liaison with BIS Office in India